Dopo aver tanto contribuito alla condivisione di idee e conoscenze, questo glorioso forum non sarà più accessibile dal 30/04/2023. Grazie a tutti/e
Pagina 35 di 62 PrimoPrimo ... 25 32 33 34 35 36 37 38 45 ... UltimoUltimo
Visualizzazione risultati 681 fino 700 di 1228
Discussione

Router per modem USB

  1. #681

    Predefinito

    Citazione Messaggio inviato da Daviez@

    se uno ha esigenze di sicurezza estreme ,
    e' meglio che non usi il wi-fi,
    non mi risulta che ci sia un sistema di cifratura inviolabile ad oggi,
    qualunque connessione puo essere sniffata e decriptata.
    se uno ha esigenze di sicurezza estreme, si tiene tutto a memoria e si fa mettere una capsula di cianuro in un dente.

  2. #682

    Predefinito

    Citazione Messaggio inviato da markk0
    se uno ha esigenze di sicurezza estreme, si tiene tutto a memoria e si fa mettere una capsula di cianuro in un dente.
    si potrebbe aprire un tread apposta ,del tipo:

    -che punta di trapano mi suggerite per un tipo di capsula?
    -ma se limono qualcuna e ci resta secca, posso dare la colpa agli hacker?

    nooooooooo, azzz , la capsula maledetti hacker!!!!!!!!

  3. #683

    Registrato il
    Jun 2005
    Età
    51
    Messaggi
    1,829

    Predefinito

    Citazione Messaggio inviato da Daviez@
    ad ALESSIO_ROMA ho dato quel consiglio solo perche aveva problemi
    a connettersi ad una rete protetta con la playstation,
    quindi niente hotfix
    , magari puo provare altri tipi di chiavi,
    magari una WPA2 come hai suggerito tu.
    Con la PS3 non servono hotfix.

    Probabilmente sei un newbie di networking e non sai muoverti a dovere fra protocolli e sistemi di protezione.

  4. #684

    Predefinito

    Citazione Messaggio inviato da arthur67
    Ciao a tutti,ho un problema con la chiavetta e172 modificata,collegandola nel router Asus WL500gpv2 e facendo le varie configurazioni compreso l'attivazione della chiavetta all'avvio del router,quando do alimentazione al router il collegamento ad internet non si avvia.mentre se entro nella configurazione del router e poi salvo e riavvio la chiavetta si collega ad internet.Cosa puo' essere?
    Ma gli id vendor e Product della chiavetta e 172 sono uguali a quelli dell'e220?se no quali sono?
    grazie.
    Nessuno può aiutarmi????

  5. #685

    Predefinito

    Citazione Messaggio inviato da Garluk
    Con la PS3 non servono hotfix.

    Probabilmente sei un newbie di networking e non sai muoverti a dovere fra protocolli e sistemi di protezione.
    amen.
    fortuna che ci sei tu , maestro,
    ad indicarmi la giusta via,
    senza te sarei perso.

  6. #686

    Predefinito

    Citazione Messaggio inviato da arthur67
    Nessuno può aiutarmi????
    cosa intendi per " chiavetta E172 modificata "?
    che firmware hai installatto nel router ?

  7. #687

    Registrato il
    Jun 2005
    Età
    51
    Messaggi
    1,829

    Predefinito

    Citazione Messaggio inviato da Daviez@
    amen.
    fortuna che ci sei tu , maestro,
    ad indicarmi la giusta via,
    senza te sarei perso.
    Si, sei proprio fortunato...peccato che per te non ci sia quasi speranza ma io non dispero e riuscirò a convincerti che gli asini non volano...

  8. #688

    Registrato il
    Jun 2005
    Età
    51
    Messaggi
    1,829

    Predefinito

    Citazione Messaggio inviato da arthur67
    Ciao a tutti,ho un problema con la chiavetta e172 modificata,collegandola nel router Asus WL500gpv2 e facendo le varie configurazioni compreso l'attivazione della chiavetta all'avvio del router,quando do alimentazione al router il collegamento ad internet non si avvia.mentre se entro nella configurazione del router e poi salvo e riavvio la chiavetta si collega ad internet.Cosa puo' essere?
    Ma gli id vendor e Product della chiavetta e 172 sono uguali a quelli dell'e220?se no quali sono?
    grazie.
    Senza elementi non ti si può certo aiutare.

    Cmq il problema da te manifestato è stato rilevato da altri (usa il tasto cerca sia qui che sul forum dell'asus) ed è probabilmente dovuto a un problema di alimentazione.

    Ovviamente gli id di una chiavetta E172 son diversi da una e220. I valori li trovi nel file di log ovvero tramite il comando dmesg

  9. #689

    Predefinito

    [QUOTE=Daviez@]cosa intendi per " chiavetta E172 modiificata "?
    che firmware hai installatto nel router ?[/QUOTE
    Ciao,scusa se non sono stato chiaro,modificata intendo sbloccata da vodafone ,uso una scheda della 3ita.Nel router ho messo il koppel 1.70a per asus v2

  10. #690

    Registrato il
    Mar 2008
    Età
    42
    Messaggi
    59

    Predefinito

    Salve a tutti.
    Ho un modem usb momodesign con sim 3.
    Ora come ora ho creato una rete domestica tra un pc dove è fisicamente collegata la chiavetta e altri 2 pc collegati via cavo.
    Volevo sapere qual'è la soluzione più economica per creare una rete domestica con un router che mi permetta di condividere la connessione tra i 3 pc fissi e via wireless con due portatili contemporaneamente (portatili+fissi tutti online nello stesso momento), ovviamente sfruttando la chiavetta 3.
    Grazie.

  11. #691

    Predefinito

    Citazione Messaggio inviato da arthur67
    Ciao,scusa se non sono stato chiaro,modificata intendo sbloccata da vodafone ,uso una scheda della 3ita.Nel router ho messo il koppel 1.70a per asus v2
    come dice GARLUK usa dmesg,

    per farlo, vai su:
    >SYSTEM SETUP
    >> SYSTEM COMMAND

    e digita nella casella piccola dmesg

    poi posta tutto

  12. #692

    Registrato il
    May 2007
    Età
    43
    Messaggi
    390

    Predefinito

    Citazione Messaggio inviato da ottogiugno
    Salve a tutti.
    Ho un modem usb momodesign con sim 3.
    Ora come ora ho creato una rete domestica tra un pc dove è fisicamente collegata la chiavetta e altri 2 pc collegati via cavo.
    Volevo sapere qual'è la soluzione più economica per creare una rete domestica con un router che mi permetta di condividere la connessione tra i 3 pc fissi e via wireless con due portatili contemporaneamente (portatili+fissi tutti online nello stesso momento), ovviamente sfruttando la chiavetta 3.
    Grazie.
    Se cerchi qui nel tread troverai i codici product vendor del tuo modem per collegarlo correttamente al Router Asus in modo tale da condividere la tua connessione di rete.
    Di qui...la soluzione più economica al tuo problema è di sicuro il WL-500gp v1 o 2 che sia

  13. #693

    Predefinito

    Citazione Messaggio inviato da Daviez@
    come dice GARLUK usa dmesg,

    per farlo, vai su:
    >SYSTEM SETUP
    >> SYSTEM COMMAND

    e digita nella casella piccola dmesg

    poi posta tutto
    Ecco il log dopo aver dato alimentazione al router

    tsu Extended Query Table v1.1 at 0x0040
    Flash Id: Vendor: 0x00c2 Device: 0x00cb
    number of CFI chips: 1
    Flash device: 0x800000 at 0x1c000000
    Physically mapped flash: squashfs filesystem found at block 739
    Creating 5 MTD partitions on "Physically mapped flash":
    0x00000000-0x00020000 : "boot"
    0x00020000-0x007f0000 : "linux"
    0x000b8f20-0x007f0000 : "rootfs"
    0x007f0000-0x00800000 : "nvram"
    0x003c0000-0x007f0000 : "flashfs"
    sflash: found no supported devices
    NET4: Linux TCP/IP 1.0 for NET4.0
    IP Protocols: ICMP, UDP, TCP, IGMP
    IP: routing cache hash table of 512 buckets, 4Kbytes
    TCP: Hash tables configured (established 2048 bind 4096)
    Linux IP multicast router 0.06 plus PIM-SM
    ip_conntrack version 2.1 (256 buckets, 2048 max) - 352 bytes per conntrack
    ip_conntrack_pptp version 1.9 loaded
    ip_nat_pptp version 1.5 loaded
    ip_tables: (C) 2000-2002 Netfilter core team
    ipt_time loading
    NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    NET4: Ethernet Bridge 008 for NET4.0
    802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
    All bugs added by David S. Miller <davem@redhat.com>
    FAT: bogus logical sector size 49920
    FAT: bogus logical sector size 49920
    NTFS: Unable to set blocksize 512.
    VFS: Mounted root (squashfs filesystem) readonly.
    Mounted devfs on /dev
    Freeing unused kernel memory: 68k freed
    Executing /linuxrc
    Algorithmics/MIPS FPU Emulator v1.5
    eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.150.10.16
    eth1: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.29
    vlan0: dev_set_promiscuity(master, 1)
    device eth0 entered promiscuous mode
    device vlan0 entered promiscuous mode
    device eth1 entered promiscuous mode
    br0: port 2(eth1) entering listening state
    br0: port 1(vlan0) entering listening state
    br0: port 2(eth1) entering learning state
    br0: port 1(vlan0) entering learning state
    br0: port 2(eth1) entering forwarding state
    br0: topology change detected, propagating
    br0: port 1(vlan0) entering forwarding state
    br0: topology change detected, propagating
    usb.c: registered new driver usbdevfs
    usb.c: registered new driver hub
    usb-ohci.c: USB OHCI at membase 0xb8003000, IRQ 6
    usb-ohci.c: usb-00:03.0, PCI device 14e4:471a
    usb.c: new USB bus registered, assigned bus number 1
    usb.c: kmalloc IF 81dfcec0, numif 1
    usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
    usb.c: USB device number 1 default language ID 0x0
    Product: USB OHCI Root Hub
    SerialNumber: b8003000
    hub.c: USB hub found
    hub.c: 2 ports detected
    hub.c: standalone hub
    hub.c: ganged power switching
    hub.c: no over-current protection
    hub.c: Port indicators are not supported
    hub.c: power on to power good time: 4ms
    hub.c: hub controller current requirement: 0mA
    hub.c: port removable status: RR
    hub.c: local power source is good
    hub.c: no over-current condition exists
    hub.c: enabling power on all ports
    usb.c: hub driver claimed interface 81dfcec0
    usb.c: kusbd: /sbin/hotplug add 1
    hub.c: port 1, portstatus 101, change 1, 12 Mb/s
    hub.c: port 1 connection change
    hub.c: port 1, portstatus 101, change 1, 12 Mb/s
    hub.c: port 1, portstatus 101, change 0, 12 Mb/s
    hub.c: port 1, portstatus 101, change 0, 12 Mb/s
    hub.c: port 1, portstatus 101, change 0, 12 Mb/s
    hub.c: port 1, portstatus 101, change 0, 12 Mb/s
    hub.c: port 1, portstatus 103, change 10, 12 Mb/s
    hub.c: new USB device 00:03.0-1, assigned address 2
    usb.c: kmalloc IF 81dfcfe0, numif 1
    usb.c: new device strings: Mfr=0, Product=0, SerialNumber=0
    hub.c: USB hub found
    hub.c: 2 ports detected
    hub.c: standalone hub
    hub.c: ganged power switching
    hub.c: global over-current protection
    hub.c: Port indicators are not supported
    hub.c: power on to power good time: 100ms
    hub.c: hub controller current requirement: 1mA
    hub.c: port removable status: RR
    hub.c: local power source is good
    hub.c: no over-current condition exists
    hub.c: enabling power on all ports
    usb.c: hub driver claimed interface 81dfcfe0
    usb.c: kusbd: /sbin/hotplug add 2
    hub.c: port 2, portstatus 100, change 0, 12 Mb/s
    hub.c: port 1, portstatus 100, change 0, 12 Mb/s
    hub.c: port 2, portstatus 101, change 1, 12 Mb/s
    hub.c: port 2 connection change
    hub.c: port 2, portstatus 101, change 1, 12 Mb/s
    hub.c: port 2, portstatus 101, change 0, 12 Mb/s
    hub.c: port 2, portstatus 101, change 0, 12 Mb/s
    hub.c: port 2, portstatus 101, change 0, 12 Mb/s
    hub.c: port 2, portstatus 101, change 0, 12 Mb/s
    hub.c: port 2, portstatus 103, change 10, 12 Mb/s
    hub.c: new USB device 00:03.0-1.2, assigned address 3
    usb.c: kmalloc IF 81915360, numif 1
    usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
    usb.c: USB device number 3 default language ID 0x409
    Manufacturer: HUAWEI Technologies
    Product: HUAWEI Mobile
    usb.c: unhandled interfaces on device
    usb.c: USB device 3 (vend/prod 0x12d1/0x1003) is not claimed by any active driver.
    Length = 18
    DescriptorType = 01
    USB version = 1.10
    Vendor:Product = 12d1:1003
    MaxPacketSize0 = 64
    NumConfigurations = 1
    Device version = 0.00
    Device Class:SubClass:Protocol = 00:00:00
    Per-interface classes
    Configuration:
    bLength = 9
    bDescriptorType = 02
    wTotalLength = 0020
    bNumInterfaces = 01
    bConfigurationValue = 01
    iConfiguration = 00
    bmAttributes = a0
    MaxPower = 500mA

    Interface: 0
    Alternate Setting: 0
    bLength = 9
    bDescriptorType = 04
    bInterfaceNumber = 00
    bAlternateSetting = 00
    bNumEndpoints = 02
    bInterface Class:SubClass:Protocol = 08:06:50
    iInterface = 00
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 83 (in)
    bmAttributes = 02 (Bulk)
    wMaxPacketSize = 0040
    bInterval = 00
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 04 (out)
    bmAttributes = 02 (Bulk)
    wMaxPacketSize = 0040
    bInterval = 00
    usb.c: kusbd: /sbin/hotplug add 3
    usb.c: registered new driver usblp
    printer.c: v0.13: USB Printer Device Class driver
    Linux video capture interface: v1.00
    SCSI subsystem driver Revision: 1.00
    Initializing USB Mass Storage driver...
    usb.c: registered new driver usb-storage
    scsi0 : SCSI emulation for USB Mass Storage devices
    Vendor: HUAWEI Model: Mass Storage Rev: 2.31
    Type: CD-ROM ANSI SCSI revision: 02
    WARNING: USB Mass Storage data integrity not assured
    USB Mass Storage device found at 3
    usb.c: usb-storage driver claimed interface 81915360
    USB Mass Storage support registered.
    usb.c: registered new driver acm
    acm.c: v0.23:USB Abstract Control Model driver for USB modems and ISDN adapters (patched)
    usb.c: registered new driver serial
    usbserial.c: USB Serial support registered for Generic
    usbserial.c: USB Serial Driver core v1.4
    usbserial.c: USB Serial support registered for Modem
    modem.c: GSM/CDMA modem driver v0.1
    usbserial.c: USB Serial support registered for PL-2303
    pl2303.c: Prolific PL2303 USB to serial adaptor driver
    usbserial.c: USB Serial support registered for FTDI SIO
    usbserial.c: USB Serial support registered for FTDI 8U232AM Compatible
    usbserial.c: USB Serial support registered for FTDI FT232BM Compatible
    usbserial.c: USB Serial support registered for FTDI FT2232C Compatible
    usbserial.c: USB Serial support registered for FTDI FT232R Compatible
    usbserial.c: USB Serial support registered for USB-UIRT Infrared Tranceiver
    usbserial.c: USB Serial support registered for Home-Electronics TIRA-1 IR Transceiver
    ftdi_sio.c: v1.3.5r1:USB FTDI Serial Converters Driver

  14. #694

    Registrato il
    Jun 2005
    Età
    51
    Messaggi
    1,829

    Predefinito

    La chiavetta viene riconosciuta correttamente.
    Qui trovi tutte le info che cercavi

    usb.c: USB device number 3 default language ID 0x409
    Manufacturer: HUAWEI Technologies
    Product: HUAWEI Mobile
    usb.c: unhandled interfaces on device
    usb.c: USB device 3 (vend/prod 0x12d1/0x1003) is not claimed by any active driver.
    Length = 18
    DescriptorType = 01
    USB version = 1.10

    Il tuo problema probabilmente è caratterizzato da una cattiva inizializzazione. Probabilmente basta mettere qualche sleep da qualche parte ma non avendo quella chiavetta non posso fare prove.

  15. #695

    Predefinito

    Citazione Messaggio inviato da the solutor
    La chiavetta non viene riconosciuta no.

    Se non si mettono pid e vid corretti ( 0x12d1/0x1003 ) nell'apposito campo, di speranze di connettersi non ce n'è.

    Sarebbe il caso che quando si fa lo spaccone, almeno si mantenga un profilo di un certo livello.

    Senza offesa, fare il cristo in terra e poi perdersi al primo (banale) log di sistema, non giova certo alla propria reputazione...


    Come scritto prima,quando vado nella configurazione del router e poi faccio save& restart la chiavetta si connette a internet normalmente.I pid e vid corretti ( 0x12d1/0x1003) sono gia inseriti.Metto il log con la chiavetta connessa a internet

    OHCI Root Hub
    SerialNumber: b8003000
    hub.c: USB hub found
    hub.c: 2 ports detected
    hub.c: standalone hub
    hub.c: ganged power switching
    hub.c: no over-current protection
    hub.c: Port indicators are not supported
    hub.c: power on to power good time: 4ms
    hub.c: hub controller current requirement: 0mA
    hub.c: port removable status: RR
    hub.c: local power source is good
    hub.c: no over-current condition exists
    hub.c: enabling power on all ports
    usb.c: hub driver claimed interface 81dfcea0
    usb.c: kusbd: /sbin/hotplug add 1
    hub.c: port 1, portstatus 101, change 1, 12 Mb/s
    hub.c: port 1 connection change
    hub.c: port 1, portstatus 101, change 1, 12 Mb/s
    hub.c: port 1, portstatus 101, change 0, 12 Mb/s
    hub.c: port 1, portstatus 101, change 0, 12 Mb/s
    hub.c: port 1, portstatus 101, change 0, 12 Mb/s
    hub.c: port 1, portstatus 101, change 0, 12 Mb/s
    hub.c: port 1, portstatus 103, change 10, 12 Mb/s
    hub.c: new USB device 00:03.0-1, assigned address 2
    usb.c: kmalloc IF 81dfcfe0, numif 1
    usb.c: new device strings: Mfr=0, Product=0, SerialNumber=0
    hub.c: USB hub found
    hub.c: 2 ports detected
    hub.c: standalone hub
    hub.c: ganged power switching
    hub.c: global over-current protection
    hub.c: Port indicators are not supported
    hub.c: power on to power good time: 100ms
    hub.c: hub controller current requirement: 1mA
    hub.c: port removable status: RR
    hub.c: local power source is good
    hub.c: no over-current condition exists
    hub.c: enabling power on all ports
    usb.c: hub driver claimed interface 81dfcfe0
    usb.c: kusbd: /sbin/hotplug add 2
    hub.c: port 2, portstatus 100, change 0, 12 Mb/s
    hub.c: port 1, portstatus 100, change 0, 12 Mb/s
    hub.c: port 2, portstatus 101, change 1, 12 Mb/s
    hub.c: port 2 connection change
    hub.c: port 2, portstatus 101, change 1, 12 Mb/s
    hub.c: port 2, portstatus 101, change 0, 12 Mb/s
    hub.c: port 2, portstatus 101, change 0, 12 Mb/s
    hub.c: port 2, portstatus 101, change 0, 12 Mb/s
    hub.c: port 2, portstatus 101, change 0, 12 Mb/s
    hub.c: port 2, portstatus 103, change 10, 12 Mb/s
    hub.c: new USB device 00:03.0-1.2, assigned address 3
    usb.c: kmalloc IF 81a244a0, numif 3
    usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
    usb.c: USB device number 3 default language ID 0x409
    Manufacturer: HUAWEI Technologies
    Product: HUAWEI Mobile
    usb.c: unhandled interfaces on device
    usb.c: USB device 3 (vend/prod 0x12d1/0x1003) is not claimed by any active driver.
    Length = 18
    DescriptorType = 01
    USB version = 1.10
    Vendor:Product = 12d1:1003
    MaxPacketSize0 = 64
    NumConfigurations = 1
    Device version = 0.00
    Device Class:SubClass:Protocol = 00:00:00
    Per-interface classes
    Configuration:
    bLength = 9
    bDescriptorType = 02
    wTotalLength = 0055
    bNumInterfaces = 03
    bConfigurationValue = 01
    iConfiguration = 00
    bmAttributes = a0
    MaxPower = 500mA

    Interface: 0
    Alternate Setting: 0
    bLength = 9
    bDescriptorType = 04
    bInterfaceNumber = 00
    bAlternateSetting = 00
    bNumEndpoints = 03
    bInterface Class:SubClass:Protocol = ff:ff:ff
    iInterface = 03
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 81 (in)
    bmAttributes = 03 (Interrupt)
    wMaxPacketSize = 0010
    bInterval = 80
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 82 (in)
    bmAttributes = 02 (Bulk)
    wMaxPacketSize = 0040
    bInterval = 00
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 02 (out)
    bmAttributes = 02 (Bulk)
    wMaxPacketSize = 0040
    bInterval = 00

    Interface: 1
    Alternate Setting: 0
    bLength = 9
    bDescriptorType = 04
    bInterfaceNumber = 01
    bAlternateSetting = 00
    bNumEndpoints = 02
    bInterface Class:SubClass:Protocol = ff:ff:ff
    iInterface = 03
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 85 (in)
    bmAttributes = 02 (Bulk)
    wMaxPacketSize = 0040
    bInterval = 00
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 05 (out)
    bmAttributes = 02 (Bulk)
    wMaxPacketSize = 0040
    bInterval = 00

    Interface: 2
    Alternate Setting: 0
    bLength = 9
    bDescriptorType = 04
    bInterfaceNumber = 02
    bAlternateSetting = 00
    bNumEndpoints = 02
    bInterface Class:SubClass:Protocol = 08:06:50
    iInterface = 00
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 83 (in)
    bmAttributes = 02 (Bulk)
    wMaxPacketSize = 0040
    bInterval = 00
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 04 (out)
    bmAttributes = 02 (Bulk)
    wMaxPacketSize = 0040
    bInterval = 00
    usb.c: kusbd: /sbin/hotplug add 3
    usb.c: kusbd: /sbin/hotplug add 3
    usb.c: kusbd: /sbin/hotplug add 3
    usb.c: registered new driver usblp
    printer.c: v0.13: USB Printer Device Class driver
    Linux video capture interface: v1.00
    SCSI subsystem driver Revision: 1.00
    Initializing USB Mass Storage driver...
    usb.c: registered new driver usb-storage
    scsi0 : SCSI emulation for USB Mass Storage devices
    Vendor: HUAWEI Model: Mass Storage Rev: 2.31
    Type: CD-ROM ANSI SCSI revision: 02
    WARNING: USB Mass Storage data integrity not assured
    USB Mass Storage device found at 3
    usb.c: usb-storage driver claimed interface 81a244d0
    USB Mass Storage support registered.
    usb.c: registered new driver acm
    acm.c: v0.23:USB Abstract Control Model driver for USB modems and ISDN adapters (patched)
    usb.c: registered new driver serial
    usbserial.c: USB Serial support registered for Generic
    usbserial.c: Generic converter detected
    usbserial.c: Buffer size for bulk_in is 4096 modem reports 64
    usbserial.c: Buffer size for bulk_out is 4096 modem reports 64
    usbserial.c: Generic converter now attached to ttyUSB0 (or usb/tts/0 for devfs)
    usb.c: serial driver claimed interface 81a244a0
    usbserial.c: Generic converter detected
    usbserial.c: Buffer size for bulk_in is 4096 modem reports 64
    usbserial.c: Buffer size for bulk_out is 4096 modem reports 64
    usbserial.c: Generic converter now attached to ttyUSB1 (or usb/tts/1 for devfs)
    usb.c: serial driver claimed interface 81a244b8
    usbserial.c: USB Serial Driver core v1.4
    usbserial.c: USB Serial support registered for Modem
    modem.c: GSM/CDMA modem driver v0.1
    usbserial.c: USB Serial support registered for PL-2303
    pl2303.c: Prolific PL2303 USB to serial adaptor driver
    usbserial.c: USB Serial support registered for FTDI SIO
    usbserial.c: USB Serial support registered for FTDI 8U232AM Compatible
    usbserial.c: USB Serial support registered for FTDI FT232BM Compatible
    usbserial.c: USB Serial support registered for FTDI FT2232C Compatible
    usbserial.c: USB Serial support registered for FTDI FT232R Compatible
    usbserial.c: USB Serial support registered for USB-UIRT Infrared Tranceiver
    usbserial.c: USB Serial support registered for Home-Electronics TIRA-1 IR Transceiver
    ftdi_sio.c: v1.3.5r1:USB FTDI Serial Converters Driver

  16. #696

    Predefinito

    Citazione Messaggio inviato da arthur67
    Come scritto prima,quando vado nella configurazione del router e poi faccio save& restart la chiavetta si connette a internet normalmente.I pid e vid corretti ( 0x12d1/0x1003) sono gia inseriti.Metto il log con la chiavetta connessa a internet
    in effetti nel primo log il modem non viene convertito,
    mentre il secondo log e' perfetto

    che modo di connessione usi?
    GPRS/EDGE/UMTS Config ?
    hai provato l'opzione zero cd configuration?

  17. #697

    Registrato il
    May 2007
    Età
    43
    Messaggi
    390

    Predefinito

    è strano però che non si connetta se non dopo un save&restart...A me capitava inizialmente con il firm 1,68 ,una volta messo l'1,69 ad ogni attacco alla corrente tempo max un minuto e si connette...
    Hai provato ad aspettare qualche minuto?Magari per la fretta non hai dato il tempo al modem di connettersi,chissà...
    Poi personalmente ho notato differenze di tempistica di collegamento a seconda dell'opzione con cui faccio la connessione,utilizzando ad esempio gprs/edge/umts ci mette di meno che non con l'opzione dial up o user dial ip,o ancora usb modem

  18. #698

    Predefinito

    Citazione Messaggio inviato da Bravo666
    è strano però che non si connetta se non dopo un save&restart...A me capitava inizialmente con il firm 1,68 ,una volta messo l'1,69 ad ogni attacco alla corrente tempo max un minuto e si connette...
    Hai provato ad aspettare qualche minuto?Magari per la fretta non hai dato il tempo al modem di connettersi,chissà...
    Poi personalmente ho notato differenze di tempistica di collegamento a seconda dell'opzione con cui faccio la connessione,utilizzando ad esempio gprs/edge/umts ci mette di meno che non con l'opzione dial up o user dial ip,o ancora usb modem
    come sopra,
    a me era capitato anche per colpa di un firmware sfortunato del modem,
    ma prima di cambiare firmware cerchiamo di escludere tutte le altre cause

  19. #699

    Predefinito

    Citazione Messaggio inviato da arthur67
    a proposito,
    che firmware hai sul modem?

    qui c'e ne uno:
    http://41.192.255.27/vcozadoc/servic....9237.B407.exe

    Edit:

    il firmware in questione va su E172 ed E272
    e ho letto che qualcuno ci ha installato anche il firmware del E170

  20. #700

    Predefinito Sarò imbranato!!!

    Ho fatto tutto quanto ho disabilita autorun su chiavetta honda hm600hs ho messo su firmware 1.70a avendo wgl600v2 con zero cd configuration non mi vede il modem devo inserire vid e pid 0x19d2/0x0001 poi apn datacard.tre.it e numero ho provato sia con *99***1# che con *99# ma nulla non si connette.Sicuramente sbaglio qualcosa posto il log per vedere se riuscite ad aiutarmi.

    usb.c: registered new driver usbdevfs
    usb.c: registered new driver hub
    usb-ohci.c: USB OHCI at membase 0xb8003000, IRQ 6
    usb-ohci.c: usb-00:03.0, PCI device 14e4:471a
    usb.c: new USB bus registered, assigned bus number 1
    Product: USB OHCI Root Hub
    SerialNumber: b8003000
    hub.c: USB hub found
    hub.c: 2 ports detected
    hub.c: new USB device 00:03.0-1, assigned address 2
    hub.c: USB hub found
    hub.c: 2 ports detected
    hub.c: new USB device 00:03.0-1.2, assigned address 3
    Manufacturer: Qualcomm, Incorporated
    Product: ONDA CDMA Technologies MSM
    usb.c: USB device 3 (vend/prod 0x19d2/0x1) is not claimed by any active driver.
    Length = 18
    DescriptorType = 01
    USB version = 1.10
    Vendor:Product = 19d2:0001
    MaxPacketSize0 = 64
    NumConfigurations = 1
    Device version = 0.00
    Device Class:SubClass:Protocol = 00:00:00
    Per-interface classes
    Configuration:
    bLength = 9
    bDescriptorType = 02
    wTotalLength = 0055
    bNumInterfaces = 03
    bConfigurationValue = 01
    iConfiguration = 00
    bmAttributes = a0
    MaxPower = 500mA

    Interface: 0
    Alternate Setting: 0
    bLength = 9
    bDescriptorType = 04
    bInterfaceNumber = 00
    bAlternateSetting = 00
    bNumEndpoints = 03
    bInterface Class:SubClass:Protocol = ff:ff:ff
    iInterface = 03
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 81 (in)
    bmAttributes = 03 (Interrupt)
    wMaxPacketSize = 0010
    bInterval = 80
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 82 (in)
    bmAttributes = 02 (Bulk)
    wMaxPacketSize = 0040
    bInterval = 00
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 02 (out)
    bmAttributes = 02 (Bulk)
    wMaxPacketSize = 0040
    bInterval = 00

    Interface: 1
    Alternate Setting: 0
    bLength = 9
    bDescriptorType = 04
    bInterfaceNumber = 01
    bAlternateSetting = 00
    bNumEndpoints = 02
    bInterface Class:SubClass:Protocol = ff:ff:ff
    iInterface = 03
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 84 (in)
    bmAttributes = 02 (Bulk)
    wMaxPacketSize = 0040
    bInterval = 00
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 04 (out)
    bmAttributes = 02 (Bulk)
    wMaxPacketSize = 0040
    bInterval = 00

    Interface: 2
    Alternate Setting: 0
    bLength = 9
    bDescriptorType = 04
    bInterfaceNumber = 02
    bAlternateSetting = 00
    bNumEndpoints = 02
    bInterface Class:SubClass:Protocol = ff:ff:ff
    iInterface = 03
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 85 (in)
    bmAttributes = 02 (Bulk)
    wMaxPacketSize = 0040
    bInterval = 00
    Endpoint:
    bLength = 7
    bDescriptorType = 05
    bEndpointAddress = 05 (out)
    bmAttributes = 02 (Bulk)
    wMaxPacketSize = 0040
    bInterval = 00
    usb.c: registered new driver usblp
    printer.c: v0.13: USB Printer Device Class driver
    Linux video capture interface: v1.00
    SCSI subsystem driver Revision: 1.00
    Initializing USB Mass Storage driver...
    usb.c: registered new driver usb-storage
    USB Mass Storage support registered.
    usb.c: registered new driver acm
    acm.c: v0.23:USB Abstract Control Model driver for USB modems and ISDN adapters (patched)
    usb.c: registered new driver serial
    usbserial.c: USB Serial support registered for Generic
    usbserial.c: Generic converter detected
    usbserial.c: Buffer size for bulk_in is 64 modem reports 64
    usbserial.c: Buffer size for bulk_out is 64 modem reports 64
    usbserial.c: Generic converter now attached to ttyUSB0 (or usb/tts/0 for devfs)
    usbserial.c: Generic converter detected
    usbserial.c: Buffer size for bulk_in is 64 modem reports 64
    usbserial.c: Buffer size for bulk_out is 64 modem reports 64
    usbserial.c: Generic converter now attached to ttyUSB1 (or usb/tts/1 for devfs)
    usbserial.c: Generic converter detected
    usbserial.c: Buffer size for bulk_in is 64 modem reports 64
    usbserial.c: Buffer size for bulk_out is 64 modem reports 64
    usbserial.c: Generic converter now attached to ttyUSB2 (or usb/tts/2 for devfs)
    usbserial.c: USB Serial Driver core v1.4
    usbserial.c: USB Serial support registered for Modem
    modem.c: GSM/CDMA modem driver v0.1
    usbserial.c: USB Serial support registered for PL-2303
    pl2303.c: Prolific PL2303 USB to serial adaptor driver
    usbserial.c: USB Serial support registered for FTDI SIO
    usbserial.c: USB Serial support registered for FTDI 8U232AM Compatible
    usbserial.c: USB Serial support registered for FTDI FT232BM Compatible
    usbserial.c: USB Serial support registered for FTDI FT2232C Compatible
    usbserial.c: USB Serial support registered for FTDI FT232R Compatible
    usbserial.c: USB Serial support registered for USB-UIRT Infrared Tranceiver
    usbserial.c: USB Serial support registered for Home-Electronics TIRA-1 IR Transceiver
    ftdi_sio.c: v1.3.5r1:USB FTDI Serial Converters Driver
    pppd 2.4.2 started by admin, uid 0
    Serial connection established.
    Using interface ppp0
    Connect: ppp0 <--> /dev/usb/tts/0
    IPCP: timeout sending Config-Requests
    Connection terminated.
    Exit.
    pppd 2.4.2 started by admin, uid 0
    Serial connection established.
    Using interface ppp0
    Connect: ppp0 <--> /dev/usb/tts/0
    IPCP: timeout sending Config-Requests
    Connection terminated.
    Exit.
    pppd 2.4.2 started by admin, uid 0
    Serial connection established.
    Using interface ppp0
    Connect: ppp0 <--> /dev/usb/tts/0
    IPCP: timeout sending Config-Requests
    Connection terminated.
    Exit.
    pppd 2.4.2 started by admin, uid 0
    Serial connection established.
    Using interface ppp0
    Connect: ppp0 <--> /dev/usb/tts/0
    IPCP: timeout sending Config-Requests
    Connection terminated.
    Exit.

Regole per postare

  • Non puoi aprire nuove discussioni
  • Non puoi rispondere
  • Non puoi inserire allegati
  • Non puoi modificare i tuoi post
  •